SATA to USB 3.0 Cable: Access a Bare 2.5-inch Drive
Your files are sitting on a drive you can't reach. This cable connects a bare 2.5-inch SATA drive straight to a USB 3.0 port, so you can copy photos, documents and old work to your desk in minutes. No tools, no case to open, and no enclosure to buy.
Read the full descriptionDescription
Your files are sitting on a drive you can't reach. This cable connects a bare 2.5-inch SATA drive straight to a USB 3.0 port, so you can copy photos, documents and old work to your desk in minutes. No tools, no case to open, and no enclosure to buy.
Connect a 2.5-inch SATA drive to any USB 3.0 port with no tools or case opening
- accessing data on a bare SATA hard drive
- need to open a computer to reach an internal drive
- moving or backing up files from an old laptop drive
Reach Your Old Laptop Drive with One Cable
Stuck with files on a drive you can't reach? Plug the bare 2.5-inch SATA drive into any USB 3.0 port and copy your data without opening a computer.
One Connector, Direct to the Drive

Seats Directly on the Drive
The 7+15 pin SATA housing seats straight onto a bare 2.5-inch drive. There is no enclosure to buy and no caddy to assemble. Line up the connector, press it on, and the drive is ready for the USB side.

Clear Blue-Tip Identification
The USB 3.0 Type-A plug carries a blue insert, so the right port is easy to spot on a crowded laptop. The plug fits any USB 3.0 port on a PC.

Molded Strain Relief
A molded strain relief sits where the cable meets the connector. That joint takes the bending and pulling that wears cables out first, so the cable holds up to repeated plugging.
From Drive to Desktop in Minutes
- 1Seat the SATA end
Line up the keyed 7+15 pin connector with the bare drive and press it on straight until it seats fully. Do not force it at an angle.
- 2Plug in the blue USB 3.0 tip
Connect the Type-A plug to a USB 3.0 port on your PC. Look for the blue insert or an SS marking.
- 3Power on and open the drive
Give the drive a moment to spin up, then check File Explorer or Disk Management. Copy your files, then use Safely Remove Hardware before you unplug.
A Single Cable, Nothing Extra
- SATA 7+15 pin connector×1
Seats directly on a bare 2.5-inch drive
- USB 3.0 Type-A plug×1
Blue insert marks the USB 3.0 end
- Cable with molded strain relief×1
Joins both ends with a reinforced junction
Characteristics
Reviews
Questions and answers
Yes, as long as your drive is a 2.5-inch SATA unit. That is the format this cable is built for, and it covers the drives most laptops shipped with. Check the drive label for SATA and the 2.5-inch size before you order.
No. This cable is built for 2.5-inch SATA drives only. For M.2 SSDs or 3.5-inch desktop drives, you need a different adapter.
The housing is matte black plastic with a budget-level finish, so treat it as a working tool rather than a heirloom. The molded strain relief at the cable junction is built for repeated plugging. Keep the cable coiled loosely and avoid yanking it out of the port.
On a USB 3.0 port, the copy runs at the speed your drive and port allow. On an older USB 2.0 port, large copies take much longer, so look for the blue insert or an SS marking. The drive's condition and the file size also set how long a copy takes.
No external power adapter is included or visible on this cable. Many 2.5-inch drives run from the USB port alone. If a drive does not spin up from a single port, connect it through a powered hub.
For one bare drive, yes. The cable skips the cost of an enclosure and the extra case you would otherwise need to hold the drive. You get a direct connection, and the same cable stays in your kit for the next drive you need to read.
Similar products
See all






