LED Work Light IP68 — 27W/48W Off-Road Spotlight for Trucks
Night falls, the rain won't quit, and you still have ground to cover. The OKEEN LED Work Light cuts through the dark with 48W of intense, IP68-sealed illumination.
Read the full descriptionDescription
Night falls, the rain won't quit, and you still have ground to cover. The OKEEN LED Work Light cuts through the dark with 48W of intense, IP68-sealed illumination.
IP68 waterproof LED work light engineered for extreme off-road and all-weather conditions
- inadequate nighttime visibility for off-roading
- work lights failing in wet/snowy conditions
- limited mounting compatibility across vehicle types
Light That Won't Quit — Rain, Snow, or Mud
When the job demands visibility and nature doesn't cooperate, the OKEEN LED Work Light delivers 48W of durable, waterproof illumination that keeps you safe and productive.
What Makes the OKEEN Different
- IP68 — Submersion Proof
We tested it in standing water, driving rain, and mud. The rubber ring seal keeps moisture out so your light keeps shining.
- Stainless Steel Flex
The bracket adjusts to any angle and tightens with stainless fasteners — no rust, no slip, even on corrugated roads.
- 16-LED Array, 48 Watts
A concentrated flood beam lights up the whole work zone. Choose 27W or 48W to match your rig's power.
The Numbers
- 27/48Two power options
- 16High-output chips
- 12-24VCompatible
- IP68Submersion rated
Mount It in 20 Minutes
- 1Choose your spot
Pick a flat surface on your bumper, roof rack, or light bar. Make sure there's clearance to adjust the angle later.
- 2Attach the bracket
Use the supplied stainless steel screws and nuts. Drill pilot holes if needed. Tighten everything down — the lock washers prevent vibration loosening.
- 3Connect the wires
Red to positive, black to negative. We strongly recommend an inline fuse (5A for 27W, 7.5A for 48W) and a dedicated switch. Wrap connections with heat-shrink tubing to protect from moisture.
- 4Aim and test
Loosen the side bolts, point the light where you need it, and re-tighten. Check the beam pattern at night before you head out.
Everything You Need to Get Lit
- LED work light×1
Your choice of 27W or 48W
- Stainless steel mounting bracket×1
Pre-attached, with angle adjustment slots
- Stainless fastenersset
Screws, nuts, lock washers
From Failure to Floodlight

Frustration After Dark
You're halfway up a mountain, rain is hammering, and your work light flickers out. Suddenly, you're operating blind — a dangerous spot. That's where OKEEN steps in.

Engineered for Survival
We built the OKEEN LED Work Light around one mantra: never fail. IP68 waterproof rated, encased in rubber with a stainless steel mounting system that stays put.

Light Where You Need It
Now, rain or shine, your worksite is lit. Mount it on a bumper, roof rack, or light bar — the beam cuts through darkness, letting you work with confidence.
Fits Where You Need It
- approx. 13.5 cmDiameter
- approx. 8 cmDepth
- extends 5 cmBracket projection
Roughly the size of a salad plate — discreet on your bumper until you hit the switch.
Why This, Not That
| OKEEN IP68 | Generic 18W | |
|---|---|---|
| Waterproof rating | ✓ IP68 | ✗ IP64 or none |
| Mount material | ✓ Stainless steel | ✗ Chrome-plated steel (rusts) |
| Adjustable angle | ✓ Yes | ✗ Fixed bracket |
| Beam quality | ✓ Focused flood | ✗ Often scattered |
| Longevity (after 1 winter) | ✓ No corrosion | ✗ Visible rust |
Characteristics
Reviews
Questions and answers
Yes. The IP68 rating means it's been tested to withstand submersion up to 1.5 meters for 30 minutes. The rubber ring seal and encapsulated electronics keep water out. You can pressure-wash it after a muddy run.
It's a simple two-wire positive/negative connection. We recommend adding an inline fuse (5A for 27W, 7.5A for 48W) and a switch if you want manual control. No relay is required for low-draw LEDs, but a professional installation is always safest.
The stainless steel bracket has elongated slots and an adjustable angle joint. It bolts up to most flat surfaces on bumpers, roof racks, bullbars, and side steps. If you can drill two holes, you can mount it.
Much brighter. The 48W model puts out a focused flood beam that illuminates a wider area instantly. It's designed as a supplementary work or off-road light, not a replacement for DOT headlights. You'll finally see the ditches.
You're paying for materials that last: stainless steel hardware, rubber sealing, and a polycarbonate lens that won't yellow. Per year of use, it costs less than replacing bargain lights every season. Plus, you aren't left in the dark when a storm hits.
Similar products
See all


