No-Drill Under-Desk Cord Rack for Clear Desk Cables
Your desk stays clear once the chargers and cables have a home under it. This no-drill rack clamps onto desk edges 1 to 5 cm thick and holds power bricks and a power strip in one open mesh basket. The side tray takes small items, and the clamp leaves the desktop untouched.
Read the full descriptionDescription
Your desk stays clear once the chargers and cables have a home under it. This no-drill rack clamps onto desk edges 1 to 5 cm thick and holds power bricks and a power strip in one open mesh basket. The side tray takes small items, and the clamp leaves the desktop untouched.
Tool-free, no-drill under-desk cable rack that clamps onto desks 1–5 cm thick
- Cables and power bricks tangled on the floor
- Cluttered desk surface
- Need for drilling into furniture
Clear the desk, keep the cables out of sight
Your chargers and cables currently spill across the floor and desktop. This no-drill rack clamps under your desk and holds them in one open mesh basket, so you can see the desk again.
Built to hold the clutter
- A clamp that holds without drilling
The C-clamp grips desks 1 to 5 cm thick, and the adjustable screws let you tighten it firmly. Because it clamps under the edge, the desktop stays untouched. Move it to another desk whenever you need to.
- Open mesh for easy access
The open metal mesh lets you see and grab a charger without unplugging everything. Cables route through the openings, so the power strip stays off the floor. The basket is 127 mm deep on both sizes. Browse more cable organizers if you run a bigger setup.
- A tray for small things
The side tray adds 60 mm of extra room for small items you reach for daily. Keep it clear of heavy bricks so the load stays centered on the clamp.
Clamp it on in three steps
- 1Measure the desk edge
Check that the edge is between 1 and 5 cm thick. The clamp will not grip a thicker edge securely.
- 2Clamp under the desk
Slide the C-clamp over the front edge from underneath and set the rack where you want it.
- 3Tighten and load
Turn the screws evenly until the rack sits steady. Place chargers and the power strip in the basket, with heavier bricks near the center.
The rack and clamp hardware
- Metal cord rack×1
Powder-coated steel mesh basket with side tray
- Clamp mounting hardware×1
C-clamp with adjustable screws
The floor is where cables end up
The floor is where cables go to tangle
Chargers slide off the desk edge and the power strip ends up on the floor. Every workday starts with a few minutes spent digging for the right cable. Clutter like this makes it harder to sit down and start.
Clamp it on, leave the desk alone
The C-clamp grips the desk edge from underneath, so nothing touches the desktop and no holes are needed. It is the right pick for rented or shared furniture where drilling is not an option. Tighten the screws and the rack sits in place.
Measured under the desk
- 340 mmLength (M)
- 400 mmLength (L)
- 127 mmBasket depth
- 205 mmClamp height
Roughly the width of a standard keyboard tray
Characteristics
Reviews
Questions and answers
The clamp fits desk edges from 1 to 5 cm thick. Measure the edge at the spot where the clamp will sit. If it is thicker than 5 cm, the rack will not grip securely.
The clamp grips the edge from underneath, so the desktop is not touched. The adjustable screws let you tighten it gently. Loosen them before you move the rack so the finish stays clean.
The basket is solid powder-coated steel mesh. Keep heavier power bricks near the center of the basket and spread the load. That keeps the clamp balanced under the desk.
Yes. Loosen the clamp, lift the rack off, and clamp it to the next desk. No holes are left behind, so the same rack works on a new desk as long as the edge is 1 to 5 cm thick.
Sleeves and adhesive clips keep cables together but leave them loose and hard to reach. This rack holds the power bricks and strip in one place for a one-time purchase, with no drilling and no adhesive to remove later.
Similar products
See all