Flexible Dryer Vent & Chimney Brush Kit, 6 Rods
Clear the full dryer vent, chimney flue, or kitchen duct without taking anything apart. Six flexible nylon rods join with aluminum connectors and bend through curves that a straight rod cannot pass, while the black brush head scrubs the inner wall. One kit covers every round duct in the house.
Read the full descriptionDescription
Clear the full dryer vent, chimney flue, or kitchen duct without taking anything apart. Six flexible nylon rods join with aluminum connectors and bend through curves that a straight rod cannot pass, while the black brush head scrubs the inner wall. One kit covers every round duct in the house.
Bendable, extendable rods reach deep into dryer vents and chimneys to clean the full inner wall
- lint buildup in dryer vents
- soot and debris in chimneys
- hard-to-reach curved ducts
- fire hazard from clogged vents
Clean the whole vent, bend and all.
Before: a dryer vent that looks clear from the front but is packed past the first bend. After: six flexible rods and one brush head carry the scrub through every curve.
Rods that follow the curve, not fight it
Rods that bend through the curve
The white nylon rods flex through an elbow and keep going, so the brush reaches the section a straight rod leaves behind. Feed them slowly, one rod at a time, and the chain follows the duct instead of fighting it.
Six rods, one reach
Each rod ends in a threaded aluminum connector, and the single-pin thread push fitting holds in either rotation direction. All six rods connected give 61cm of total reach. Measure your run before you start so you know whether one session will cover it.
Brush the inner wall
The round black bristle head sits on the rods and scrubs the inner wall of a round duct as you turn it. Dense nylon bristles on a rigid hub press against the metal instead of skimming past the lint.
Six rods, one brush, 61cm of reach
- 6flexible rods in the kit
- 61cmtotal reach with all rods connected
- 1round brush head
Feed, twist, and pull the lint out
- 1Unplug and open the duct
Switch off the dryer or the breaker, then detach the vent at the back so you can reach the run from the exhaust end.
- 2Join two rods
Thread two rods together by hand until the aluminum connector seats firmly. Add rods one at a time as the run gets longer.
- 3Feed the brush in
Push the brush head into the duct and let the rods bend through each curve. Go slowly at elbows so the joints do not separate.
- 4Twist and pull
Turn the rods by hand, or fit a power drill to the end for a faster scrub. Pull the chain back out and vacuum the loosened lint.
Clean the vent, not only the trap
The bend you cannot see
You empty the lint trap after every load, and the dryer can still take two cycles to finish a load. The trouble sits past the first elbow, where lint builds up unseen and the duct narrows a little more each season.
Reach past the elbow
Six rods join with threaded aluminum connectors and bend through the curve while the brush rides along. A straight rod stops at the first turn. This chain keeps going and scrubs the inner wall as it moves.
A clear vent, one weekend
Once the brush has run the full vent and flue, the lint comes out in clumps and the dryer runs at a normal pace again. Put a seasonal clean on the calendar, and the next load starts from a clear run.
Why a straight rod stops at the first bend
| This kit | Straight rod kit | Vacuum hose | |
|---|---|---|---|
| Bends through elbows | — | — | |
| Brush scrubs the inner wall | Partial | — | |
| Rod length | 6 flexible rods | Rigid rods | Hose only |
| Works with or without a drill | Partial | — |
Characteristics
Reviews
Questions and answers
The rods total 61cm with all six connected, and the brush head is made for round ducts. Measure the straight length from the back of the dryer to the outside exit before you order. If the run is longer than 61cm, clean it in sections from both ends.
Yes. The kit is built for dryer vents, chimney flues, and round ducts such as kitchen exhaust. For a flue, connect the rods to the brush head, push up in sections, and twist as you go to scrub soot from the inner wall.
Yes. You can turn the rods by hand. A drill speeds up the scrub on a long run, but it is not required.
The brush is dense nylon on a rigid hub, and the connectors are threaded aluminum that seat firmly on a single-pin joint. Check the bristles and joints before each season. Replace the brush head if tufts are bent or a connector no longer seats.
A single clogged vent can cost more than this kit. Cleaning the vent yourself costs only your time, and the kit covers dryer, chimney, and kitchen ducts, so you can repeat the clean every season.
Similar products
See all
Flexible Dryer Vent & Chimney Brush Kit, 6 Rods